Introduction
The “Tank Low” error message on a GE Washer can be confusing, especially if you don’t know what it means or how to fix it. In this article, we’ll explain what the “Tank Low” error means, provide some troubleshooting steps, and discuss how to fix the problem.
Explaining What Does “Tank Low” Mean on a GE Washer
The “Tank Low” error message refers to the water level in the washer. When the water level is too low, the washer will display the “Tank Low” error message. This error can occur for a variety of reasons, including a blocked drain pump filter or a faulty pressure switch.
To understand the causes of the “Tank Low” error, it’s important to first understand how the washer works. The washer has two tanks: one for the wash cycle and one for the rinse cycle. During the wash cycle, water from the main tank is pumped into the wash tank. During the rinse cycle, water from the rinse tank is pumped back into the main tank. If there isn’t enough water in either tank, the washer won’t be able to complete the cycle.
Troubleshooting the “Tank Low” Error on a GE Washer
If your washer displays a “Tank Low” error message, there are a few troubleshooting steps you can take before attempting to fix the problem. First, check the water supply to make sure it’s turned on and that the water pressure is adequate. If the water supply is adequate, then the next step is to clean out the drain pump filter. If the filter is clogged, it can prevent the washer from filling up with water.
Next, check the pressure switch hoses for any signs of damage or blockages. If the hoses are damaged or blocked, they may need to be replaced. Finally, check the pressure switch itself. If the switch is faulty, it can cause the washer to display a “Tank Low” error message.
How to Fix the Tank Low Error on a GE Washer
If the troubleshooting steps above don’t solve the problem, then it’s time to start thinking about replacing parts. The most likely culprit is the pressure switch. If the pressure switch is faulty, it can cause the washer to display a “Tank Low” error message. To replace the pressure switch, you’ll need to unplug the washer and remove the back panel. Then, disconnect the wiring harness from the pressure switch and replace it with a new one.
If the pressure switch isn’t the problem, then the next likely culprit is the water inlet valve. The water inlet valve controls the flow of water into the washer. If the valve is faulty, it can cause the washer to display a “Tank Low” error message. To replace the water inlet valve, you’ll need to unplug the washer and remove the back panel. Then, disconnect the wiring harness from the valve and replace it with a new one.
Understanding the Signs of a Tank Low Error on a GE Washer
In addition to displaying a “Tank Low” error message, there are other signs that can indicate a tank low error. These include noisy operation, unusual smells, and unusual sounds. If your washer is exhibiting any of these symptoms, it’s a good indication that there is a problem with the water level in the washer.
Preventing and Fixing Tank Low Errors on GE Washers
The best way to prevent tank low errors is to perform regular maintenance on your washer. This includes checking and cleaning the drain pump filter regularly, as well as checking the pressure switch hoses for any signs of damage or blockage. Additionally, avoid overloading the washer, as this can cause the water level to drop too low.
Finally, using high-efficiency detergents can help reduce the amount of foam produced during the wash cycle, which can help keep the water level in the washer at an optimal level. If you’re still having problems with a tank low error, consult the owner’s manual for more detailed instructions on how to troubleshoot and fix the problem.
Conclusion
The “Tank Low” error message on a GE Washer can be confusing and frustrating. However, by understanding what the error means and following the troubleshooting and fixing steps outlined in this article, you should be able to get your washer running smoothly again in no time.
If you’re still having issues with a tank low error, contact a qualified repair technician for further assistance. With the right knowledge and tools, you can quickly and easily fix the problem and get your washer back up and running.
